Quick Answer: How To Replace The Carburetor On Poulan P295 Chainsaws?

How do you change the carburetor on a Poulan Pro chainsaw?

This article provides step-by-step instructions for replacing the carburetor on a Poulan chainsaw.

  1. Let’s get started.
  2. Remove the top cover.
  3. Remove the air filter housing.
  4. Remove the carburetor.
  5. Remove the starter assembly.
  6. Disconnect the fuel lines.
  7. Remove the purge bulb.
  8. Remove the choke lever.

Why does my Poulan chainsaw dies when I give it gas?

The fuel filter might be clogged. A clogged fuel filter is often caused by leaving old fuel in the chainsaw. Over time, some of the ingredients in the fuel may evaporate, leaving behind a thicker, stickier substance. This sticky fuel can clog up the fuel filter and cause the engine to stall.

How do you remove the carburetor from a Poulan Pro chainsaw?

How to Replace the Carburetor on a Poulan Pro Chainsaw

  1. Let’s get started.
  2. REMOVING THE CARBURETOR 1. Drain the fuel.
  3. Remove the air filter.
  4. Remove the starter assembly.
  5. Remove the top cover.
  6. Remove the air filter base.
  7. Remove the choke lever.
  8. Disconnect the throttle linkage.
You might be interested:  Readers ask: What Is The Pilot Screw Setting For A Keihin Carburetor?

Can’t get my Poulan chainsaw started?

If your Poulan chain saw won’t start, the first thing to check is the fuel. Then turn the saw on, hold it firmly and pull the start rope in short, brisk pulls until it starts. If it doesn’t start within 15 pulls, the spark plug is likely wet-fouled. Remove it and check for moisture on the electrode.

Why does my chainsaw dies when I give it gas?

Because your chainsaw will idle, but dies when it is revved up to full power, it means that the filter is only partially clogged; it will allow enough fuel to the engine to run on idle, but not enough to sustain full throttle. If the filter becomes clogged, not enough fuel will reach the engine for it to run properly.

Why does my chainsaw bog out when I give it gas?

If your chainsaw is bogging down when you give it throttle, this is often a sign of improper gas-to-oil ratio. If there is too much gasoline in relation to the amount of oil used, this is known as a “rich mixture” and can cause the chainsaw to run poorly.

How do you adjust the high and low on a Poulan chainsaw?

High and Low Speed Adjustments Start the chain saw as you normally do and let it idle, making sure the chain does not touch anything. Insert a small flat-head screwdriver into the idle speed screw and turn it clockwise to increase the engine speed if it idles too slowly.

How do you troubleshoot a Poulan chainsaw?

Poulan Pro Chainsaw Troubleshooting

  1. Make sure you are starting the engine properly.
  2. Fill the tank with the correct fuel mixture.
  3. Clean the saw blade.
  4. Check the fuel line for kinks or leaks.
  5. Replace the fuel filter.
  6. Clean the air filter.
  7. Remove and replace the spark plug.
You might be interested:  Readers ask: How To Put On An Aftermarket Carburetor?

Where is the gas filter on a Poulan chainsaw?

A: The fuel filter is located in the fuel tank. We recommend changing the fuel filter yearly. To remove the filter, drain your unit of fuel and remove the fuel cap/retainer assembly from the tank. Pull the filter from the tank and remove it from the end of the fuel line.

How do I get my chainsaw to idle?

First set the idle speed by setting it as high as possible without engaging the clutch (close to 2700 RPM if you have a tachometer). Then set the low-speed screw by turning it gently in until the engine begins to starve for fuel, then turn it out gently until the engine loads up.

Leave a Reply

Your email address will not be published. Required fields are marked *