- 1 How do I identify my Holley carb?
- 2 How do I tell what model my carburetor is?
- 3 What do the numbers on a Holley carb mean?
- 4 How do you date a Holley carb?
- 5 What’s the difference between Holley 4150 and 4160?
- 6 What size carburetor do I need for a 350?
- 7 What CFM is a Holley 4160?
- 8 Did Holley buy demon?
- 9 Are all Holley Metering blocks the same?
- 10 How do you troubleshoot a Holley carburetor?
- 11 What is a Holley 3310?
How do I identify my Holley carb?
It’s like a “VIN” for your carburetor and should be hand-stamped on the front of the choke tower to the right of the vent tube on most typical Holley carbs. The list number typically is four to six digits long and may or may not have a suffix number behind it. The date code will be right below it.
How do I tell what model my carburetor is?
The list number is stamped on your carburetor, either on the corner of the airhorn or choke tower or, if it doesn’t have an airhorn, on the mainbody. Remove the carburetor from your vehicle before looking for the list number to easily find the information you need.
What do the numbers on a Holley carb mean?
The first three numbers indicate the day of the year; the last digit, the year of manufacture. Here, “2889” indicates a carb made on the 288th day (which falls in the month of October), of a year ending in 9 (1969, 1979, 1989, 1999, etc.).
How do you date a Holley carb?
Moving on, 0798 is our date code; Holley used a three digit up to 1973, after which they moved to the four digit code you see here. Decoding them is as follows: Three Digit – Example 763 > 7 – Year (1967), 6 – Month (June), 3 – (Third Week)
What’s the difference between Holley 4150 and 4160?
These two are very similar with the primary difference that the 4150 uses a thick metering block in both the primary and secondary while the 4160 is shorter in length and uses a thin, metering plate on the secondary side.
What size carburetor do I need for a 350?
A 600-cfm carburetor may perform quite well on a stock 350 Chevy. However, the minute you start weaving in power adders like a hotter cam, a dual-plane performance intake manifold, and aluminum heads you’re going to need 700-750 cfm.
What CFM is a Holley 4160?
Holley 0-80457S Model 4160 600 CFM Square Flange 4-Barrel Vacuum Secondary Electric Choke Carburetor.
Did Holley buy demon?
We reported that BG Fuel Systems and Demon Carburetors were poised for a comeback in a blog earlier this week. The fact that the company was bought by High Performance Industries, the same company that owns Holley, Demon’s biggest competitor, has created a bit of a stir in the automotive aftermarket.
Are all Holley Metering blocks the same?
The primary metering blocks for a center hung and side humg 4150 and 4160 are completely interchangeable.
How do you troubleshoot a Holley carburetor?
(1) Remove air horn and check float settings. (2) Check float needle and seat for proper seal. If the needle is defective, replace with a Holley matched set. (3) Check float for being loaded with fuel, bent float hanger or binding of the float arm.
What is a Holley 3310?
Once described as the small block Chevy of fuel delivery, the Holley 3310 carburetor (4150 and 4160 models) is still the go-to carburetor for anyone building a performance engine. The legendary Holley 3310 was born. The 3310 feeds the Z16 Chevelle’s 396 big block with 780 cfm of air.